百度
A test turntable may carry sensors, fixtures or control electronics while the base remains fixed. Draw the interface boundary before choosing a slip ring. Label every electrical path crossing it and identify the USB connection separately. This prevents a product name from substituting for a system design. The application sheet identifies the selected unit as a turntable slip ring with a 38.1 mm through bore, twenty 2 A circuits and one USB 2.0 group. Those figures make it a useful reference, but the final pin map and operating limits must come from the approved drawing.
A through bore can give the machine designer a central route for a shaft, cable bundle or other assembly, depending on the final geometry. Measure the complete stack, including fasteners, service clearance and cable movement, rather than checking nominal bore diameter alone. The source notes 38.1 mm; the machine team should verify the controlled dimension and tolerance. If the test fixture or harness occupies that space, document it on the installation drawing so the electrical and mechanical teams do not plan to use the same volume twice.
Twenty 2 A circuits and a USB 2.0 group are different kinds of interface. State which circuits power loads, which carry control or feedback and which pins are reserved. For USB, define the devices, cable length, connectors and acceptable behavior during rotation. The source record says the product can transmit USB 2.0; it does not publish throughput, error rates or a universal cable-length guarantee. Ask for test evidence under the intended configuration rather than interpreting the protocol name as a promise of every possible application.
A turntable’s speed, acceleration, direction changes and duty cycle affect the assembly around the slip ring. The selected row does not provide rotational speed or torque for this model. Set these as project requirements and request confirmation. Check that fixed-side and rotating-side leads have proper strain relief and do not twist, rub or obstruct the fixture. In a compact test rig, access for installation and service may be as important as the diameter on the component drawing.
Commissioning should verify every assigned electrical circuit, the USB connection and the intended motion with the real fixture attached. Record the drawing revision, test equipment, connection layout and pass criteria. A short bench test may miss a failure that appears after repeated direction changes or with a longer machine harness. For regional equipment teams coordinating several suppliers, keep one shared interface schedule and one owner for changes. That handover makes the final system easier to reproduce and support.
An engineering inquiry should include the circuit list, USB device type, target bore clearance, installation envelope, rotation profile and expected environment. A sketch showing the stationary and rotating sides is often more useful than a photograph alone. JINPAT can then confirm whether the documented project configuration or a different design fits the machine. This article is a selection guide, not a claim that the referenced unit has been installed across Asia or meets unspecified standards.
The buyer should decide whether the acceptance test covers the slip ring alone or the complete installed connection. For USB, the latter includes the host, cables and device; for current circuits it includes the connected loads and return paths. A product-level result can be useful for supplier qualification, but it is not identical to machine-level behavior. Record both where practical. This distinction helps an Asian machine builder coordinate separate component and system teams without assigning the same test to everyone or leaving a gap between them.
Before the design is frozen, hold a review involving mechanical, electrical, controls and test engineers. Mechanical engineering should confirm the bore and mounting envelope. Electrical engineering should approve circuit allocation and cable exits. Controls engineering should identify the USB device and software behavior. Test engineering should define repeatable pass criteria. The selected product gives the meeting a concrete reference configuration, but the group must decide what applies to the actual turntable. Record unresolved questions with owners instead of converting them into marketing claims.
The order in which the shaft, slip ring, fixture and harness are assembled can change the accessible space. Ask whether the component can be installed after the central shaft is fitted and whether a connector can be reached for service. Check the minimum bend area for the attached cables in every position. A drawing that shows only the final assembly may hide a difficult installation step. A simple assembly sequence or mock-up can reveal this before procurement commits to a housing layout.
If the fixture grows, the USB peripheral changes or the circuit schedule expands, review the rotary interface again. A small machine change can affect bore clearance, cable routing or test conditions. Keep the product drawing, wiring map and acceptance plan at the same revision. That controlled package helps several regional suppliers work from identical information and prevents a late substitute from being judged against an obsolete requirement. The website article can remain general while the customer-specific package stays precise.
The photography sheet says the images have been cut out and watermarked, which makes them useful for explaining scale and appearance after final approval. A photo cannot establish USB performance, electrical ratings or the exact mounting tolerance. Show the product with a neutral turntable diagram if needed, but avoid placing unverified figures on the image. Check that filenames, alt text and graphics do not expose the internal project code. A good article lets the drawing and test report support the claims while the photo helps the reader understand the form.
Editorial note: The source row records a 38.1 mm through bore, 20 circuits rated 2 A, one USB 2.0 group, turntable use and cut-out watermarked images. Confirm all final electrical and mechanical limits against an approved drawing before publication. Do not show the internal project code.